Many old houses have affirmed and they seem to have been hard to deal with: dense, hard, and fragile. That being said, it’s not really that difficult to hang stuff on plaster walls, as much as you are using hooks and operate gradually and deliberately to maintain a good fit, pre-drill the holes, and use relatively long screws. Use hooks with connectors for maximum safety if you are holding large objects. In this Blog we are we are going to provide you in depth guide about How to hang heavy things on plaster walls.
How to hang heavy things on plaster walls?
If you do have picture rail, use that
A narrow piece of timber that passes from around circumference of a room, usually about 2.5-cm to 30-cm) far below base of the roof, has some earlier plaster walls If you have this in your place, you can just drive a screw through the wood and then use it to hang stuff. For example, on the place just above you would like to hang a photo, push a wrench into the strip. To get the photo to the perfect height, you can lift or drop the cable.
Put down a drop fabric
Set a drop fabric or an old sheet immediately down the floor wherever you want something on the wall to display. Dust and scraps can be formed by holes drilled into plaster. Putting the fabric down would make it a breeze to tidy up.
Gather materials for you
You won’t need something special or complicated, and if you’re not using this already, you can find it in a supermarket. You will need one:
- Pack of screws with a length of 1.25-inches or 2-inches to hang heavy items
- Painter’s Roll of Tape
- Ballpoint pen
- Drill and a set of bits for the drill
- Tape to measure
- Lever of Carpenter’s
- Stud Finder Magnetic (optional)
- Wire roll for holding an object (optional)
Label the place you want the object to hang from
On the wall, put a piece of painter’s tape approximately wherever you want the item to be. The measuring tape is then used to determine the height of the precise place. Using a ball pen to mark it on the painter’s tape. When you dig into it, the painter’s tape will help protect the plaster from breaking.
Make a hole pre-drill
Carrying a wider drill bit than the size of the screws that you’ve used. For example, when you use screws 0.25-inches deep, use a drill bit that is 3⁄16-inches wide. At the spot you’ve marked, push the bit into the wall. Act thoroughly, sticking the drill to the wall at a perfect distance. Plaster is heavy, so there’s some friction you’ll encounter. If the drill reaches the lathe, the friction can increase.
You can also Check : Best Concrete Sealers
Drive a wrench into the place you have labeled
On your drill, turn to a screwdriver extension. Drive a wrench through it nearly all the way.
Hang the item
Place one end of a string from around screw head securely. On the item you would like to hang, tie other end to the hook or help. Change the length of the wire until you have the item at the level you like. Many items will also have a hole in the bottom (like several picture frames) that you can place specifically on the screws to keep it in place.
Using hardware for heavy duty application
Using hooks that are 2 inches (5.1 cm) long to cover heavy objects on plaster walls. Get supplies that have flexible anchor connections if necessary to help keep it in place.
Use a stud
Retrieve the wooden studs concealed behind plaster wall using a static stud finder. When they are kept in place by threads forced into the stud, heavy items would be more stable.
When they locate a stud, many stud locators will glow. Label the place on the wall if you find a stud. To build a horizontal line going up the wall from this location, and use a measuring tape. Label the height along that line where you really want to hang the item on a piece of tape for the painter. Without pressing screws into a stud, you can place heavy objects on plaster walls. To be more stable, nevertheless, you must use screws with anchors.
At the place where you want to hang the piece, pre-drill a hole
For standing light objects, use the same technique as you would do. Even so, if you’re using one, ensure to use a drill bit that is just a little smaller than the diameter of the anchor.
-For example, an anchor that is 0.3-inches wide can have a screw that is 0.25-inches wide. Using a drill bit that does not exceed 0.25-inches.
Tap the anchor into the hole
Simply use the strength on your palm, if necessary. Tap it softly with a soft iron until it becomes flush with the wall, if the anchor does not go that direction. Even so, be very patient. Plaster is fragile and will crack if you strike it with the handle unintentionally. At a hardware store, look for one. Essentially, you have to smear the substance into the affected area carefully, clean it out, and let it set up.
Drive in the anchor with the screw
This should be reasonably straightforward, but to do it rapidly, you can now use the drill with a screw connection. Don’t drive all the way in with the screw. Leave a slight gap between the head of the screw and the wall’s surface. Connect the hand rail to the screw on the plaster wall on the object’s back. To ensure that it is even, check the location of your object with a level.
If required, install more screws
Put more screw in the wall on the side of the first, that use the same method, whether the object is big or very heavy. This will help spread the object’s weight and keep it on the wall more stable. Drive the next screw into a stud if necessary.
If you are hanging several items, mark out the screw positions
Start with the position of the first screw, if you want to hang multiple objects at the same height. Find out the distance between the center of both objects next to each other. Label the distance to the right or left of the first screw by using your measuring tape and a pencil. Quantify up or down from the minute window if you want the objects to sit at various elevations.
Most shelves consist of a series of anchors that keep the shelving information up (usually 2-3). Typically, these anchors need at least 2 screws each. Place the anchor in place, then put a screw in. For the second, pre-drill a hole and mount the screw. Measure the necessary length to the right or left of the first one to mount the extra anchors. To ensure that the next anchor will be even with the very first, set a level on the line generated by your tape measure. Like you did with the first anchor, mount the screws.
We are sorry that if this post was not useful for you!
Let us improve this post!
Tell us how we can improve this post?